Manufacturing of PCB has been simplified through innovation and advancement in technology. You will require a photo resist board which forms the basics of the entire assembly. This is a piece of glass with reinforcements made of plastic. On the one end is a photo sensitive copper coating. It is by peeling this plastic film that one reveals the photo sensitive coating.
The printed circuit board that is already transparent goes below the photo resist board. These two boards should be of the same size. The sensitivity of this surface is arrived at by removing the plastic film. The boards should be aligned to ensure that your tracks do not end up in any other way apart from what you intended. This is the level of manufacture that prepares the board for placement into the UV light box.
An appropriate cover for the box should be sort to make it effective. Your board should be in the box for around two and half minutes after which it is removed. Plastic tongs should be used in handling the board considering that it is delicate during manufacture. It is then transferred into a specially prepared development box for about ten seconds. Allowing it to stay more than that exposes it to damage. The tracks may be destroyed completely.
Plastic tongs are used to transfer the board to the etching tank after it has been thoroughly cleaned using water. The box is switched on for heating until bubbles form. This process is supposed to remove excel copper material in order to leave the tracks clean and clear. This process should be closely monitored to ensure that the tracks are not damaged.
Etching will take approximately fifteen minutes. Under-etching exposes the board incomplete development while it will get damaged when etching is overdone. The tracks are likely to be removed in the process. The process of manufacture should be monitored by the minute and will eventually be mastered.
The layout for PCB is best produced using an auto CAD or Computer Aided Design system. This is a system that allows you to input your own data and later transfer it to your manufacturer. The system allows you to earmark and define the copper layers you need for each job. The component notations and soldier marks will also be clear.
A controlled dark room makes preparation of photo tools easier. This is done using laser driven photoplotters. The room has the right temperature and humidity conditions for work. Converting the data used in manufacture of the images into a pixel image simplifies the process of manufacture. The film is written using a laser writer. The film is ready for unloading by the operator after automatic film development.
Profiling or V-cut scoring is the process that completes manufacturing of PCB. The process takes place at the production panel and uses a scoring machine. A third of the board is cut to ensure that it remains intact. Engaging an expert ensures that the entire process of manufacture meets your expectations.
The printed circuit board that is already transparent goes below the photo resist board. These two boards should be of the same size. The sensitivity of this surface is arrived at by removing the plastic film. The boards should be aligned to ensure that your tracks do not end up in any other way apart from what you intended. This is the level of manufacture that prepares the board for placement into the UV light box.
An appropriate cover for the box should be sort to make it effective. Your board should be in the box for around two and half minutes after which it is removed. Plastic tongs should be used in handling the board considering that it is delicate during manufacture. It is then transferred into a specially prepared development box for about ten seconds. Allowing it to stay more than that exposes it to damage. The tracks may be destroyed completely.
Plastic tongs are used to transfer the board to the etching tank after it has been thoroughly cleaned using water. The box is switched on for heating until bubbles form. This process is supposed to remove excel copper material in order to leave the tracks clean and clear. This process should be closely monitored to ensure that the tracks are not damaged.
Etching will take approximately fifteen minutes. Under-etching exposes the board incomplete development while it will get damaged when etching is overdone. The tracks are likely to be removed in the process. The process of manufacture should be monitored by the minute and will eventually be mastered.
The layout for PCB is best produced using an auto CAD or Computer Aided Design system. This is a system that allows you to input your own data and later transfer it to your manufacturer. The system allows you to earmark and define the copper layers you need for each job. The component notations and soldier marks will also be clear.
A controlled dark room makes preparation of photo tools easier. This is done using laser driven photoplotters. The room has the right temperature and humidity conditions for work. Converting the data used in manufacture of the images into a pixel image simplifies the process of manufacture. The film is written using a laser writer. The film is ready for unloading by the operator after automatic film development.
Profiling or V-cut scoring is the process that completes manufacturing of PCB. The process takes place at the production panel and uses a scoring machine. A third of the board is cut to ensure that it remains intact. Engaging an expert ensures that the entire process of manufacture meets your expectations.
About the Author:
when you want information about manufacturing of PCB, visit our home pages at www.becman.com today. You can see details on the product at http://www.becman.com now.